Willkommen bei MattzoBricks › Foren › Sensors › MattzoSensorController
- Dieses Thema hat 5 Antworten und 3 Teilnehmer, und wurde zuletzt aktualisiert vor 3 Jahren, 2 Monaten von Zoltan.
-
AutorBeiträge
-
-
Februar 3, 2021 um 21:58 Uhr #2113Nikos LygizosTeilnehmer
I tried a different plate to hold the hull sensor parallel to the tracks and until now it is working very well.
Using 11458 – “Lego Plate, Modified 1×2 with Pin Hole on Top” for the sensor and 63864 – “Tile 1×3” to hold 11458 to the rail ties.Enjoy!
Nikos- Dieses Thema wurde geändert vor 3 Jahren, 3 Monaten von Matthias Runte.
- Dieses Thema wurde geändert vor 3 Jahren, 2 Monaten von Nikos Lygizos.
- Dieses Thema wurde geändert vor 2 Jahren, 11 Monaten von Max.
-
Februar 8, 2021 um 15:05 Uhr #2288Paul VerkaikTeilnehmer
Hello Everyone,
I’m having some trouble with the sensorcontroller. Up to 7 sensors it works ok, as soons as I connect sensor 8 , the control-led turns on and does not go off.
I think that I have connected everything ok, sensor 1-7 to D1-7 and ground, sensor 8 to D8 and 3v3. and also the control-led to D0 and gnd.
I tried another sensor but the same effect.
Any ideas??Greetings,
Paul
-
Februar 8, 2021 um 16:06 Uhr #2289Paul VerkaikTeilnehmer
Argh !! Never mind, fixed it !
Me not doing basic troubleshooting, and me using el-cheapo chinese components was the problem.
3! sensors in a row were defective, so using my multi-meter, testing before soldering yet another one did the trick.
Lesson learned (again): never assume, make sure!BTW love the idea above from Nikos !
Greetings,
Paul
-
Februar 9, 2021 um 07:58 Uhr #2290Nikos LygizosTeilnehmer
Thank you Paul!
By the way, I got my sensors from Amazon and I did not have any issues with them:
DIYhz Reed Switch GPS-14A 14mm Plastic Anti-Interference Normally Open Magnetic Control Switch 10PCS
- Diese Antwort wurde geändert vor 3 Jahren, 2 Monaten von Nikos Lygizos.
-
-
-
Februar 20, 2021 um 11:21 Uhr #2447ZoltanTeilnehmer
Ich habe für mein Spur-G-Testprojekt den Sensorcontroller fertig gebaut:
Auslösermagnet unter der “Lok” Neodym 3 * Ø6mm, dicke 2mm (entspricht Ø6*6 mm);
Sensor in Legostein zwischen den Schwellen, fest genug und doch und bewegbar, wenn es sein muss:
Funktioniert 🙂
-
März 3, 2021 um 09:33 Uhr #2627ZoltanTeilnehmer
Mein “Projekt” ist fertig.
Wie schon erwähnt, MattzoBricks Lego Automation hat mich fasziniert!
Aber ich habe keine Lego Züge. Ich wollte es aber trotzdem ausprobieren. So habe ich das Projekt etwas geändert (in den Äusserlichkeiten), und auf Spur G als Test umgesetzt. Hier ist ein Bericht über den Bau der “Rückmelder”.
-
-
AutorBeiträge
- Du musst angemeldet sein, um auf dieses Thema antworten zu können.